VEX100H+V Compact Units

VEX140-150-160-170 Horisontal and Vertikal
General

VEX100 range

VEX140, 150 and 160 can be ordered  in either a Horizontal or Vertical version, whereas VEX170 can only be ordered in Horizontal.

This is a very flexible range of units, which can be ordered as LEFT or RIGHT and with spigot locations in the side, top or bottom.

 

VEX100H V placering

            Horizontal                                          Vertical

Operating conditions

In principle, EXHAUSTO VEX units are designed for use in comfort ventilation - i.e. under ordinary operating conditions.

Where ventilation solutions are required for rooms with high air humidity - e.g. due to humidification, we recommend you make a test calculation with one of our calculation programs. If the calculation shows a risk of condensation after the heat exchanger, an assessment must be made whether the operating conditions can be changed, or whether the unit must be modified to allow condensate to drain off. This is particularly relevant for VEX100CF.

Contact EXHAUSTO for advice on this.

Capacity, VEX100

The diagram below illustrates the capacity ranges covered by the individual VEX sizes. 

To calculate actual capacity data, use our product selection programmes.

Cuves Capacity VEX100


Design

VEX100

The compact units are designed in accordance with German hygiene standard VDI6022, which ensures that units are accessible for service and that formation of mould or other bacteria that could negatively impact air quality is prevented. Read more about this standard under certificates at the bottom of the page.

Cabinets

 
 Kabinet_VEX200

Cabinets are made from Aluzinc® AZ185 class C4 in accordance with EN/ISO 12944-2 and insulated with 50 mm mineral wool. This results in low noise emissions to the surrounding environment/installation room.

The panel design minimises the formation of thermal bridges in the unit.

Motor sections

 

The motor sections are mounted in vibration dampers, which reduces noise in the ducts and eliminates the need to fit flexible connections between the unit and the duct system.

The motor sections can be extracted for easier servicing.

The motors are of type EC and are extremely efficient. They comply with the requirements of the Ecodesign Directive.

Fan impeller

 

EXstream performance.

The units are equipped with EXHAUSTO EXstream impellers, one of the leading air fan impellers on the market in terms of low energy consumption and low sound emissions.

Connection box

 

VEX100 Mainboard

The easily accessible connection box with built-in isolator switch and control fuses ensures easy access for connection and adjustment. 

Panel filters

 
 

Panel filters are easy to replace and can be ordered as filter class Coarse 85% (M5) or ePM1 55% (F7) in acc. with EN779.

 

Heating coil - water or electric 

 
 VEX100 varmeflade The VEX100 range is supplied with an integrated heating coil, heated either by water or electricity

Mounting base

 
 VEX200_sokkel A mounting base with adjustable feet is supplied standard. The base height is adjustable 130–160 mm.
The unit must be assembled at the bottom using the base and via the closures on the top.
Energy

VEX100

The design of the air handling units has focussed in particular on achieving as smooth as possible airflow through the air handling units in order to achieve the lowest possible pressure loss.


Cross-flow heat exchanger

 
 
 Krydsvarmeveksler

Aluminium cross-flow heat exchanger with low pressure drop and high temperature efficiency. The cross-flow heat exchanger ensures full separation of airways, preventing transfer of odours or pollutants to the supply air.

Standard: Well suited for process ventilation - a lot of space between panels means simple cleaning



EC-Motors

 
 
EC-motor_MC The combination of modern EC motors and the EXHAUSTO motor controller delivers extremely low energy consumption and with the EXstream fan impeller, high output is achieved.


Energy label

 
 
energilabel
An energy label that states the energy class of the air handling unit in relation to defined operating conditions is available via our product calculation programs.


Certificates

VEX100/VEX100CF/VEX200/VEX300

EXHAUSTO puts great emphasis on providing accurate data. So we use a third party to measure and check our data.

Eurovent certification

All data provided with the VEX100/VEX100CF/VEX200/VEX300 model has been measured.

The units have completed a major test programme in our development department and all of the capacity, efficiency and sound data is collected via testing and in real operating situations.

  I følge Eurovent test/-godkendelse iht. EN1886 og EN13053 opfylder EXHAUSTO VEX-aggregater følgende krav/klasser:

Unit’s stiffness:
D1(M)
  Air tightness class at -400 Pa : 
L1 (M)
  Air tightness class at +700 Pa:
L1 (M)
  Filter bypass leakage:
F9 (M)
  Insulation class:
T2 (M), U1≤1,0
  Thermal bridge class:
TB3 (M)

This means that a third party has checked that the data that our product calculation program produces complies with the real performance of the unit. Eurovent checks the data by selecting a unit at random and testing that unit at their own facility. If our stated data complies with the Eurovent's test results, we retain our certification. This guarantees the customer that our data is valid.


VDI6022 - German hygiene standard

EXHAUSTO has designed its units in accordance with the German hygiene standard VDI6022.

VDI6022 requirements
The unit's design must make cleaning easy. There may not be areas that cannot physically be cleaned and voids that are inaccessible must be sealed. Plates must be deburred to ensure edges are smooth and corners must be rounded to avoid the risk of injury when cleaning.

In addition,the condensation tray must decline to the outlet, so that water cannot remain in the unit. It is important that the condensation outlet is connected to the drainage system on a horizontal surface.

All non-metallic materials (e.g. seals, filters), are tested to show that they do not promote growth of mould spores and bacteria.


Because the unit is designed in accordance with VDI6022, it is both more hygienic and easier to clean.


Ecodesign

Ecodesign - EU requirements for documentation, energy consumption and labelling of ventilation units.

 

 

General information

We have made a compilation of extracts from the Ecodesign guidelines, read more about Ecodesign under Institute.

ECO-design-logo

Ecodesign data

You will find links to Ecodesign data for the individual VEX sizes under the product name and under Download, where we have located Ecodesign data under EU/ECO declarations.

NB:

We would point out that the values stated in the declarations have been calculated for a specific operating point.

If a different operating point is desired, we would refer you to our calculation programs - here you can see whether the desired unit meets the requirements for your operating point and find the associated Ecodesign data.


SPLIT version

VEX100 is available as a split version.

With some projects, limited space means that internal transport of the air handling unit is difficult or impossible. This is why the VEX100 is available as a split version. It means that the air handling unit can be assembled and tested at the factory as normal – just without sealant. The air handling unit can therefore be easily taken apart at the installation site, transported as single sections, assembled, sealed and commissioned.

The table below shows the dimensions of the largest section (crossflow heat exchanger) and largest cabinet section, so that it can easily be determined whether there is sufficient space to allow internal transport.

Section Dimensions VEX140 VEX150 VEX160 VEX170
Crossflow heat exchanger Height [mm] 525 632 735 842
Length [mm] 525 632 735 840
Depth [mm] 655  737 842 1142
Weight [kg]
 27 38 46 85
Biggest cabinet section Height [mm]  1360 1600 1820  2200 
Width [mm]
 940 1090  890  1190 
Motor section Weight [kg]  2 x 16.5 2 x 23.5 2 x 33  2 x 54

VEX170 eksploderet til Split

VEX100 SPLIT version


Accessories

VEX100

A wide range of accessories are available with the VEX100 range.

Cooling coils - CW

 
CCW firkantet studs Cooling coil - is available insulated or non-insulated. A flexible solution is to cool ventilation air in those rooms that require it, e.g. south-facing rooms. Frequently, north-facing rooms do not require cooling.

More information about the cooling coil is found in the section Cooling and heating coils.

Cooling coils - DX

 
DX cooling 150100

Non-insulated external coil that can be used both as an evaporator (cooling coil) and condenser (heating coil).

 

More information about the DX coils is found under Cooling and heating coils 

Closing damper - LS

 
Lukkespjæld firkantet studs Closing damper with or without spring-return, for indoor or outdoor fitting.

 Water trap

 

EXHAUSTO also offers a water trap for the unit's condensation drain in dimension DN32.

SIPHONUP (negative pressure) for connection to condensation outlet from the unit.
SIPHONOP (overpressure) for connection to any cooling coil in the supply air duct.

SIPHONHE02 (accessory) hot-wire is used to keep the water trap and water pipe free of ice. A thermostat is fitted to the hot wire to ensure low energy consumption.

Outdoor installation

 
 
VEX240 med tag

The cabinet is insulated with 50 mm mineral wool and therefore well-suited for outdoor installation.

For outdoor installation, the air handling unit will be delivered with a roof which allows cables to be routed out from under the roof on both sides, as well as the rear of the air handling unit.

We recommend that air handling units which are installed outdoors, are secured further as described in the Outdoor-manual.

Add all about the product series VEX100H+V Compact Units

CONTACT US TODAY

Get free advice on ventilation products and system solutions


Export Requests:
EXHAUSTO Export
Odensevej 76
DK 5550 Langeskov

Tel +45 6566 1236
E-mail: export@exhausto.dk

Calculation programs

Use EXHAUSTO's free calculation programs for calculating ventilation plant and system solutions

Go to Calculation Programs
Teaser ecodesign

Ecodesign Directive

EXHAUSTO VEX air handling units and fans comply with the Ecodesign Directive. Read more here.

See more about Ecodesign here