VEX150CF H-V

VEX150CF is available in horizontal and vertical versions

Technical data

Technical data, VEX150CF

Unit data

Min. airflow
725 m³/h
Max. airflow
3,160 m³/h
Absorbed power 2,7 kW
Power supply 3 x 400 V + N + PE ~ 50 Hz
Max. phase current 8,7 A  *
Max. neutral current 15.0 A 
Weight
Operation-ready unit 330 kg
For transport into the location 207 kg**
Motor and motor control (MC) data
Motor type EC motor
Motor class in accordance with IEC TS 60034-30-2 IE5 (Ultra Premium Efficiency)
Voltage input 1 x 230 V
Current overload protection Built-in
Regulation Variable via motor control (MC)
Control signal With integrated control system:
Modbus
For third-party control system:
0-10 V DC
* (power consumption is not sinusoidal)
** (excl. doors, heat exchanger and fan units)
 

Heating coils

Electric heating coil (HCE) 12.0 kW
Absorbed power total 14.7 kW
Power supply 3 x 400 V + N + PE~ 50 Hz
Max. phase current 26.0 A
Electric heating coil (HCE) 18.0 kW
Absorbed power total 20.7 kW
Power supply 3 x 400 V + N + PE~ 50 Hz
Max. phase current 34.7 A
Water heating coil (HCW)

Test pressure
3000 kPa
Max. operating pressure
1000 kPa
Number of rows of pipes
Qty. 2
Number of circuits
Qty. 5
Face area (H x W)
425 x 655 mm.
Pipe connection
DN15 (½")
Fin spacing
2,1 mm.
Weight (without fluid)
8,7 kg.
Water content
2,2 l.

Fan data

 
Max. total efficiency (A-D) 60.0 %
ECO measurement set-up (A-D) A
Efficiency level requirements 62N (2015)
ECO efficiency level during optimal operating point 74.4N

Motor data (optimal operating point)

EC motor With motor controller
Absorbed power 1.25 kW
Airflow 3279 m3/h
Total pressure 826 Pa
RPM during optimal operating point 2902

Conditions:
- Density = 1.2 kg/m3
- Pressure ratio < 1.11
- other points in acc. with EC327/2011 (see product instructions)

Temperature efficiency

Temperature efficiency, VEX150CF

The temperature efficiency and, to a lesser extent, the SFP/SEL values for a specific air handling unit are closely connected to the heat exchanger itself and depend upon the manufacturer. As suppliers can change from time to time, small changes in the technical data can occur, which is why it is always recommended that you perform a calculation for the particular project using our calculation software, EXselectPRO.

VEX150CF temperature efficiency
The curve is intended as a guideline, and it is recommended that a calculation be performed using the calculation software EXselectPRO for the individual project.

stiplet streg
Efficiency with condensation:
Extract air = 20°C/55 RH
Outdoor air  = -10°C/50 RH
Balance between supply air/extract air = 1,0
kort-lang-stiplet-streg
Efficiency without condensation with imbalance:
Extract air = 25°C/28 RH
Outdoor air = 5°C/50 RH
Balance between supply air/extract air  = 0,8
fed streg Efficiency without condensation in acc. with EN308:
Extract air = 25°C/28 RH
Outdoor air = 5°C/50 RH
Balance between supply air/extract air = 1,0

 

 

Calculation

The temperature efficiency of the VEX units is shown at different airflow ratios, calculated as:


t2.1 = Temperature of outdoor air (fresh air)
t2.2 = Temperature of supply air
t1.1 = Temperature of extract air
Extract air = 25 ºC / 30 % RH
Outdoor air (fresh air) = 5 ºC / 50 % RH
Temperature efficiency is stated in accordance with EN308 for dry heat recovery and is increased by condensation.
Dimensional drawings horizontal

Dimensional drawings, VEX150CF-H

VEX150CF-H - Horizontal, Left (unit dimensions in mm)

Dim VEX150CF HL

desired spigot location, position A or B, to be specified in order.
*) Allow a height for service in front of the unit equivalent to the unit width.
**) Allow a min. of 300 mm free height for service.

 

VEX150CF-H - Horizontal,Right (unit dimensions in mm)

Dim VEX150CF HR


1.1 Extract air 1.2 Exhaust air 2.1 Outdoor air 2.2 Supply air

 desired spigot location, position A or B, to be specified in order.
*) Allow a height for service in front of the unit equivalent to the unit width.
**) Allow a min. of 300 mm free height for service.

Dimensional drawings vertical

Dimensional drawings, VEX150CF-V 

VEX150CF-V - Vertical, Left (unit dimensions in mm)

Dim VEX150CF VL

 desired spigot location, position A or B, to be specified in order.
*) Allow a height for service in front of the unit equivalent to the unit width.
**) Allow a min. of 300 mm free height for service.

 

VEX150CF-V - Vertical, Right (unit dimensions in mm)

Dim VEX150CF VR


1.1 Extract air 1.2 Exhaust air 2.1 Outdoor air 2.2 Supply air

 desired spigot location, position A or B, to be specified in order.
*) Allow a height for service in front of the unit equivalent to the unit width.
**) Allow a min. of 300 mm free height for service.

Cooling and heating coils

Cooling and heating coils, VEX150CF

The following cooling and heating coils are suitable for VEX150/VEX150CF

Type Model
CW cooling coil (water)  CW400I
CW400U
DX cooling/heating coil DX400

Add all about the product series VEX150CF H-V

CONTACT US TODAY

Get free advice on ventilation products and system solutions


Export Requests:
EXHAUSTO Export
Odensevej 76
DK 5550 Langeskov

Tel +45 6566 1236
E-mail: export@exhausto.dk

Calculation programs

Use EXHAUSTO's free calculation programs for calculating ventilation plant and system solutions

Go to Calculation Programs
Vex overview

VEX Summary

Get a quick overview of our entire range of compact VEX air handling units with heat recovery.

View the VEX summary here